Commandes de plus de
$5000TI ISO5852SMDWREP
Driver 5A 2-OUT Inv/Non-Inv 16-Pin SOIC T/R
Marques: Texas Instruments
Pièce Fabricant #: ISO5852SMDWREP
Fiche de données: ISO5852SMDWREP Fiche de données (PDF)
Colis/Caisse: 16-SOIC
type de produit: Galvanically Isolated Gate Drivers
Statut RoHS:
État des stocks: 9 726 pièces, nouveau original
Warranty: 1 Year Ovaga Warranty - Find Out More
0
1
ISO5852SMDWREP Description générale
The ISO5852S-EP device is a 5.7-kVRMS, reinforced isolated gate driver for IGBTs and MOSFETs with split outputs, OUTH and OUTL, providing 2.5-A source and 5-A sink current. The input side operates from a single 2.25-V to 5.5-V supply. The output side allows for a supply range from minimum 15-V to maximum 30-V. Two complementary CMOS inputs control the output state of the gate driver. The short propagation time of 76 ns provides accurate control of the output stage.
An internal desaturation (DESAT) fault detection recognizes when the IGBT is in an overcurrent condition. Upon a DESAT detect, a mute logic immediately blocks the output of the isolator and initiates a soft-turnoff procedure which disables the OUTH pin and pulls the OUTL pin to low over a time span of 2 µs. When the OUTL pin reaches 2 V with respect to the most-negative supply potential, VEE2, the gate-driver output is pulled hard to the VEE2 potential which turns the IGBT immediately off.
When desaturation is active, a fault signal is sent across the isolation barrier pulling the FLT output at the input side low and blocking the isolator input. Mute logic is activated through the soft-turnoff period. The FLT output condition is latched and can be reset only after the RDY pin goes high, through a low-active pulse at the RST input.
When the IGBT is turned off during normal operation with a bipolar output supply, the output is hard clamp to VEE2. If the output supply is unipolar, an active Miller clamp can be used, allowing Miller current to sink across a low-impedance path which prevents the IGBT from dynamic turnon during high-voltage transient conditions.
The readiness for the gate driver to be operated is under the control of two undervoltage-lockout circuits monitoring the input-side and output-side supplies. If either side has insufficient supply, the RDY output goes low, otherwise this output is high.
The ISO5852S-EP device is available in a 16-pin SOIC package. Device operation is specified over a temperature range from –55°C to +125°C ambient.
Caractéristiques
- 100-kV/μs Minimum Common-Mode Transient Immunity (CMTI) at VCM = 1500 V
- Split Outputs to Provide 2.5-A Peak Source and 5-A Peak Sink Currents
- Short Propagation Delay: 76 ns (Typ), 110 ns (Max)
- 2-A Active Miller Clamp
- Output Short-Circuit Clamp
- Soft Turn-Off (STO) during Short Circuit
- Fault Alarm upon Desaturation Detection is Signaled on FLT and Reset Through RST
- Input and Output Undervoltage Lockout (UVLO) with Ready (RDY) Pin Indication
- Active Output Pulldown and Default Low Outputs with Low Supply or Floating Inputs
- 2.25-V to 5.5-V Input Supply Voltage
- 15-V to 30-V Output Driver Supply Voltage
- CMOS Compatible Inputs
- Rejects Input Pulses and Noise Transients Shorter Than 20 ns
- Operating Temperature: –55°C to +125°C Ambient
- Surge Immunity 12800-VPK (according to IEC 61000-4-5)
- Safety-Related Certifications:
- 8000-VPK VIOTM and 2121-VPK VIORM Reinforced Isolation per DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
- 5700-VRMS Isolation for 1 Minute per UL 1577
- CSA Component Acceptance Notice 5A, IEC 60950-1, IEC 60601-1 and IEC 61010-1 End Equipment Standards
- CQC Certification per GB4943.1-2011
- All Certifications Complete per UL, VDE, CQC, TUV and Planned for CSA
Caractéristiques
Paramètre | Valeur | Paramètre | Valeur |
---|---|---|---|
Manufacturer | Texas Instruments | Product Category | Galvanically Isolated Gate Drivers |
RoHS | Details | Series | ISO5852S-EP |
Mounting Style | SMD/SMT | Package / Case | SOIC-16 |
Minimum Operating Temperature | - 55 C | Maximum Operating Temperature | + 125 C |
Technology | Si | Brand | Texas Instruments |
Features | DESAT Protection, Split Output, Miller Clamp, Power Good, Fault Output, Reset, Soft Turn Off | Moisture Sensitive | Yes |
Product | Isolated Gate Drivers | Product Type | Galvanically Isolated Gate Drivers |
Propagation Delay - Max | 110 ns | Factory Pack Quantity | 2000 |
Subcategory | PMIC - Power Management ICs | Part # Aliases | V62/16623-01XE |
Number of channels | 1 | Isolation rating | Reinforced |
Withstand isolation voltage (VISO) (Vrms) | 5700 | Working isolation voltage (VIOWM) (Vrms) | 2121 |
Transient isolation voltage (VIOTM) (VPK) | 8000 | Power switch | IGBT, MOSFET, SiCFET |
Peak output current (A) | 5 | Output VCC/VDD (max) (V) | 30 |
Output VCC/VDD (min) (V) | 15 | Input VCC (min) (V) | 2.25 |
Input VCC (max) (V) | 5.5 | Propagation delay time (µs) | 0.076 |
Input threshold | CMOS | Operating temperature range (°C) | -55 to 125 |
Rating | HiRel Enhanced Product | Bus voltage (max) (V) | 2121 |
Rise time (ns) | 18 | Fall time (ns) | 20 |
Undervoltage lockout (typ) (V) | 12 |
Expédition
Type d'expédition | Frais d'expédition | Délai de mise en œuvre | |
---|---|---|---|
DHL | $20.00-$40.00 (0.50 KG) | 2-5 jours | |
FedEx | $20.00-$40.00 (0.50 KG) | 2-5 jours | |
UPS | $20.00-$40.00 (0.50 KG) | 2-5 jours | |
TNT | $20.00-$40.00 (0.50 KG) | 2-5 jours | |
EMS | $20.00-$40.00 (0.50 KG) | 2-5 jours | |
LA POSTE AÉRIENNE ENREGISTRÉE | $20.00-$40.00 (0.50 KG) | 2-5 jours |
Délai de traitement : les frais d'expédition dépendent des différentes zones et pays.
Paiement
Modalités de paiement | Frais de main | |
---|---|---|
Virement bancaire | facturer des frais bancaires de 30,00 $ US. | |
Pay Pal | facturer des frais de service de 4,0 %. | |
Carte de crédit | facturez des frais de service de 3,5%. | |
Western union | charge US.00 banking fee. | |
Paiement de Petit Montant | facturer des frais bancaires de 0,00 $ US. |
Garanties
1. Les composants électroniques que vous achetez incluent une garantie de 365 jours, nous garantissons la qualité du produit.
2. Si certains des articles que vous avez reçus ne sont pas de qualité parfaite, nous organiserons de manière responsable votre remboursement ou votre remplacement. Mais les articles doivent rester dans leur état d’origine.
Emballage
-
Étape1 :Produit
-
Étape2 :Emballage sous vide
-
Étape3 :Sac antistatique
-
Étape4 :Emballage individuel
-
Étape5 :Boîtes d'emballage
-
Étape6 :étiquette d'expédition à code-barres
Tous les produits seront emballés dans un sac antistatique. Expédié avec une protection antistatique ESD.
L'étiquette de l'emballage extérieur ESD utilisera les informations de notre société : numéro de pièce, marque et quantité.
Nous inspecterons toutes les marchandises avant expédition, garantirons que tous les produits sont en bon état et que les pièces sont neuves et correspondent à la fiche technique originale.
Une fois que toutes les marchandises sont garanties sans problème après l'emballage, nous les emballerons en toute sécurité et les enverrons par Global Express. Il présente une excellente résistance à la perforation et à la déchirure ainsi qu’une bonne intégrité du joint.
Nous fournissons des produits de haute qualité, un service attentionné et une garantie après-vente
-
Nous avons des produits riches, pouvons répondre à vos différents besoins.
-
La quantité minimum de commande commence à partir de 1 pièce.
-
Les frais d'expédition internationaux les plus bas commencent à partir de 0,00 $
-
Garantie de qualité de 365 jours pour tous les produits