Ce site web utilise des cookies. En utilisant ce site, vous consentez à l'utilisation de cookies. Pour plus d'informations, veuillez consulter notre politique de confidentialité.

Commandes de plus de

$5000
bénéficient $50 d'une remise !

WINBOND W83977AF

PLUG & PLAY1.0ACOMPLIANT

ISO14001 ISO9001 DUNS

Marques: WINBOND

Pièce Fabricant #: W83977AF

Fiche de données: W83977AF Fiche de données (PDF)

Colis/Caisse: QFP128

Statut RoHS:

État des stocks: 6 554 pièces, nouveau original

Warranty: 1 Year Ovaga Warranty - Find Out More

Citation courte

Veuillez soumettre une demande de prix pour W83977AF ou envoyez-nous un email: E-mail: [email protected], nous vous contacterons dans les 12 heures.

W83977AF Description générale

GENERAL DESCRIPTIONThis data sheet covers two products: W83977F, and W83977AF whose pin assignment, and most of the functions are the same. W83977AF is an advanced version of W83977F featuring the FIR function.FEATURESGeneral• Plug & Play 1.0A Compliant• Support 13 IRQs, 4 DMA channels, full 16-bit addresses decoding• Capable of ISA Bus IRQ Sharing• Compliant with Microsoft PC97 Hardware Design Guide• Support DPM (Device Power Management), ACPI• Programmable configuration settings• 24 or 14.318 Mhz clock inputFDC• Compatible with IBM PC AT disk drive systems• Variable write pre-compensation with track selectable capability• Support vertical recording format• DMA enable logic• 16-byte data FIFOs• Support floppy disk drives and tape drives• Detects all overrun and underrun conditions• Built-in address mark detection circuit to simplify the read electronics• FDD anti-virus functions with software write protect and FDD write enable signal (write data signal was forced to be inactive)• Support up to four 3.5-inch or 5.25-inch floppy disk drives• Completely compatible with industry standard 82077• 360K/720K/1.2M/1.44M/2.88M format; 250K, 300K, 500K, 1M, 2M bps data transfer rate• Support 3-mode FDD, and its Win95 driverUART• Two high-speed 16550 compatible UARTs with 16-byte send/receive FIFOs• 3rd UART with 32-byte send/receive FIFO is supported for IR function [W83977AF only]• MIDI compatible• Fully programmable serial-interface characteristics:   --- 5, 6, 7 or 8-bit characters   --- Even, odd or no parity bit generation/detection   --- 1, 1.5 or 2 stop bits generation• Internal diagnostic capabilities:   --- Loop-back controls for communications link fault isolation   --- Break, parity, overrun, framing error simulation• Programmable baud generator allows division of 1.8461 Mhz and 24 Mhz by 1 to (216-1)• Maximum baud rate up to 921k bps for 14.769 Mhz and 1.5M bps for 24 MhzInfrared• Support IrDA version 1.0 SIR protocol with maximum baud rate up to 115.2K bps• Support SHARP ASK-IR protocol with maximum baud rate up to 57,600 bps• Support IrDA version 1.1 MIR (1.152M bps) and FIR (4M bps) protocol [W83977AF only]   --- Single DMA channel for transmitter or receiver   --- 3rd UART with 32-byte FIFO is supported in both TX/RX transmission [W83977AF only]   --- 8-byte status FIFO is supported to store received frame status (such as overrun CRC error, etc.)• Support auto-config SIR and FIR [W83977AF only]Parallel Port• Compatible with IBM parallel port• Support PS/2 compatible bi-directional parallel port• Support Enhanced Parallel Port (EPP) - Compatible with IEEE 1284 specification• Support Extended Capabilities Port (ECP) - Compatible with IEEE 1284 specification• Extension FDD mode supports disk drive B; and Extension 2FDD mode supports disk drives A and B through parallel port• Enhanced printer port back-drive current protectionAdvanced Power Management (APM) Controlling• Power turned on when RTC reaches a preset date and time• Power turned on when a ring pulse or pulse train is detected on the PHRI, or when a high to low transition on PWAKIN1, or PWAKIN2 input signals• Power turned on when PANSW input signal indicates a switch on event• Power turned off when PANSW input signal indicates a switch off event• Power turned off when a fail-safe event occurs (power-save mode detected but system is hung up)• Power turned off when software issues a power off commandKeyboard Controller• 8042 based with optional F/W from AMIKKEYTM-2, Phoenix MultiKey/42TM or customer code with 2K bytes of programmable ROM, and 256 bytes of RAM• Asynchronous Access to Two Data Registers and One status Register• Software compatibility with the 8042 and PC87911 microcontrollers• Support PS/2 mouse• Support port 92• Support both interrupt and polling modes• Fast Gate A20 and Hardware Keyboard Reset• 8 Bit Timer/ Counter; support binary and BCD arithmetic• 6, 8, 12, or 16 Mhz operating frequency (16 Mhz available only if input clock rate = 14.318 Mhz)

Caractéristiques

  • General
  • Plug & Play 1.0A Compliant
  • Support 13 IRQs, 4 DMA channels, full 16-bit addresses decoding
  • Capable of ISA Bus IRQ Sharing
  • Compliant with Microsoft PC97 Hardware Design Guide
  • Support DPM (Device Power Management), ACPI
  • Programmable configuration settings
  • 24 or 14.318 Mhz clock input
WINBOND Inventory

Expédition

Type d'expédition Frais d'expédition Délai de mise en œuvre
DHL DHL $20.00-$40.00 (0.50 KG) 2-5 jours
Fedex FedEx $20.00-$40.00 (0.50 KG) 2-5 jours
UPS UPS $20.00-$40.00 (0.50 KG) 2-5 jours
TNT TNT $20.00-$40.00 (0.50 KG) 2-5 jours
EMS EMS $20.00-$40.00 (0.50 KG) 2-5 jours
LA POSTE AÉRIENNE ENREGISTRÉE LA POSTE AÉRIENNE ENREGISTRÉE $20.00-$40.00 (0.50 KG) 2-5 jours

Délai de traitement : les frais d'expédition dépendent des différentes zones et pays.

Paiement

Modalités de paiement Frais de main
Virement bancaire Virement bancaire facturer des frais bancaires de 30,00 $ US.
Pay Pal Pay Pal facturer des frais de service de 4,0 %.
Carte de crédit Carte de crédit facturez des frais de service de 3,5%.
Western union Western union charge US.00 banking fee.
Paiement de Petit Montant Paiement de Petit Montant facturer des frais bancaires de 0,00 $ US.

Garanties

1. Les composants électroniques que vous achetez incluent une garantie de 365 jours, nous garantissons la qualité du produit.

2. Si certains des articles que vous avez reçus ne sont pas de qualité parfaite, nous organiserons de manière responsable votre remboursement ou votre remplacement. Mais les articles doivent rester dans leur état d’origine.

Emballage

  • Produit

    Étape1 :Produit

  • Emballage sous vide

    Étape2 :Emballage sous vide

  • Sac antistatique

    Étape3 :Sac antistatique

  • Emballage individuel

    Étape4 :Emballage individuel

  • Boîtes d'emballage

    Étape5 :Boîtes d'emballage

  • étiquette d'expédition à code-barres

    Étape6 :étiquette d'expédition à code-barres

Tous les produits seront emballés dans un sac antistatique. Expédié avec une protection antistatique ESD.

L'étiquette de l'emballage extérieur ESD utilisera les informations de notre société : numéro de pièce, marque et quantité.

Nous inspecterons toutes les marchandises avant expédition, garantirons que tous les produits sont en bon état et que les pièces sont neuves et correspondent à la fiche technique originale.

Une fois que toutes les marchandises sont garanties sans problème après l'emballage, nous les emballerons en toute sécurité et les enverrons par Global Express. Il présente une excellente résistance à la perforation et à la déchirure ainsi qu’une bonne intégrité du joint.

  • ESD
  • ESD

Nous fournissons des produits de haute qualité, un service attentionné et une garantie après-vente

  • Produit

    Nous avons des produits riches, pouvons répondre à vos différents besoins.

  • quantity

    La quantité minimum de commande commence à partir de 1 pièce.

  • shipping

    Les frais d'expédition internationaux les plus bas commencent à partir de 0,00 $

  • garantie

    Garantie de qualité de 365 jours pour tous les produits

Notes et avis

Notes
Veuillez évaluer le produit !
Merci de saisir un commentaire

Veuillez soumettre vos commentaires après vous être connecté à votre compte.

Soumettre